Visitor No.5767702 ..   
TrustPassKenplas Industry Ltd.Discussion Forum
 
Kenplas Forum ==> Machine Trouble Shooting ==> FAQ VS600
<< Previous Topic Next Topic >>
1
1 - pet blow Machine VS-600, serial nº 200789, ------- Need you send to us the certificate with good quality by email like we send in atach.

1 - chiller Model KLA_3, serial nº 270712626, ------- Need the manual and certificate of conformity

1 - high pressur compressor Model STA155,SERIAL Nº 20053

1 - Auto Load pre forms, ------- Need the manual and certificate of conformity


Please send for us The Manual of each machine and Certificates of conformity, also tell us email of your comercial saller to send prices for Moulds and others.

Best Regards,

Rui Silva

Fine
Poor
11/7/2011 1:33:07 AM By rui silva
Someone has the machine instruction manual in pdf Kenplas VS600

If someone can send thank you very much Email: luis.povoa@petrovagos.pt

Thank you

Fine
Poor
10/15/2011 2:41:01 AM By luispovoa
The top solenoid is quite warm. Is this normal or could it be part of the problem?
Yes, it is normal.

Fine
Poor
1
12/14/2007 11:00:44 PM By Kenplas
Bybass Valve
If using one high pressure air compressor, just switch on the valve shown as enclosed, then switch off the gate valve for low pressure air inlet.

Fine
1
Poor
12/14/2007 10:51:32 PM By Kenplas
Bottom Mold Installation

Fine
Poor
12/14/2007 10:46:31 PM By Kenplas
When temperature inside heating tunnel reaches this temperature setting, exhaust blowing fan will be triggered. Temperature shown in RED is the real temperature inside heating tunnel (e.g. 112), and temperature show in GREEN is setting temperature (e.g. 24).

Fine
Poor
12/11/2007 10:59:06 AM By Kenplas
Also inside the electic board there is a unit where you can set a temperature? What is this for?

Fine
Poor
12/11/2007 10:58:26 AM By Nikos
Up On: 8 zone heating.
0: 4 zone heating.
Down On: 10 zone heating.

Fine
Poor
12/11/2007 10:57:40 AM By Kenplas
Inside the electic board there is a switch with Up ON middle 0 and down ON. What is this for please?

Fine
Poor
12/11/2007 10:57:12 AM By Nikos
Three reasons:
1. Under automatic mode, if no preform detected (blowing signal), MOLD-CLOSE will not come. Thus if the photo sensor (blowing signal) doesn't focus on preform well, which will lead to same problem.
2. If focus length of this photo sensor is too far, it may detect the mold platen, thus mold may close one cycle and idle one cycle even there is no preform.
3. Reduce the air flow a little bit through two throttle valves shown in attached photo.

P.S. On this photo sensor, GREEN light is power indicator, and RED light is on when preform is detected.

Fine
Poor
12/11/2007 10:55:52 AM By Kenplas
While the machine working without blowing the mould does not close at each time. it closes one by one. Is this normal?

Fine
Poor
12/11/2007 10:54:34 AM By Nikos
when machine starts, "preform rotation" starts. Rotation chain runs clockwise if view from top. Chain speed is fixed.

Fine
Poor
12/11/2007 10:53:26 AM By Kenplas
We receive today the machine and the impressions at the begining are very nice. Please send us the parametres for the trial of 5lt and 10lt.
Also we want the temperatures and the parameters of the programm.
What is the rotation of the preform because from the manual I can not understand it. Please see figure 'rotation'. Can the speed of preform potation be adjusted or it is stable?

Fine
1
Poor
12/11/2007 10:49:22 AM By Nikos
1
 
 

Post A Reply

Temporarily shut down, no new message, sorry.

Name:

Email:

Message:

(Max. 2KB)



Attachment:     (Max. 500kB, .RAR.ZIP.JPG.GIF only)
Verification:

This forum published since July 03, 2002. Renewed on June 22, 2005.

[Plastics Project] [Plastics Machinery] [Plastics Mold] [Discussion Forum] [Contact Kenplas]
Copyright © 2017 Kenplas Industry Limited, Hangzhou Kenplas Machinery Ltd.              Powered by Alentus.