Visitor No.6005810 ..   
TrustPassKenplas Industry Ltd.Plastics MachineryPET Stretch Blow Molding Machine
 

NB5G Stretch Blow Molding Machine

H.S.Code: 8477300000
PET Stretch Blow Molding Machine model NB5G
Running Video of NB5G
(Size: 2.33Mb, Duration 1'24")
Typical Parts
  • Pneumatic related (Low Pressure), FESTO/Germany;
  • Pneumatic related (High Pressure), FESTO/Germany + SMC/Japan;
  • Controller (with Touch LCD), Inverter, Mitsubishi/Japan;
  • Contactor, Relay, Switch, Schneider/Germany;
CE NormTypical Feature
  • Circumstance Independent
    NB5G runs stably, whether voltage is 200V or 240V, or whether room temperature is 00C or 400C.
  • Easy Operation
    Minimum parameter settings (through touch LCD), normally only temperature settings should be regulated, no need to play with time settings;
    Multi-language interfaces;
  • Reliability
    Completely new-concept design, more mechanical & synchronized design to reduce fault to minimum level.
  • Energy-saving
    Air recycling unit to save compressed air 20~25% (for 5 Gallon);
    Reduced heating power;
    Driving is mostly done by motor directly, instead of compressed air.
  • Higher Output
    200% more efficient than traditional one.
  • Fast Mold Changeover
    Adopts Aluminum mold, lighter to be installed or unloaded;
    10 molding data memories to make mold changeover quicker.
Specification
Model NB5G
General Heater Type Infrared
Capacity 400BPH: 300g Non-returnable 19L;
250BPH: 700g        Returnable 19L;
450BPH: 250g 12L;
550BPH: 180g 10L
600BPH: 150g   8L;
Bottle Vol. 8 ~ 20 Litre
Cavity 1 Cavity
Bottle Diameter <=290 mm
Outer Neck Diameter 45~55 mm (*1)
Bottle Height <=530 mm
Cooling Water Water Pressure 3~5 Bar
Water Flow 5000L/h
Temperature 6-10 0C
Chiller Capacity 18000 Kcal/h
Air Driving Air 0.0 m3/min (when recycle used)
Blowing Air 26~30Bar, <=3.0 m3/min. (*2)
Power Total Power 39.7 Kw
Heater Power 32 Kw
Machine Dimension see below diagram
Weight 3300 kgs
Interface Air Inlet G3/4"
Water Inlet G3/4"
Delivery Time 75 Days
Payment Term 30% T/T advance as deposit, balance 70% by L/C at sight.

(*1) -- different necks one same machine needs extra charge on parts to fit necks.

(*2) -- depending on bottle size and operating condition. Rated output of air compressor should be at least 50% higher than this value.

Overview of NB5G

Overview of NB5G

Layout of NB5G

Layout of NB5G

Referece Bottles
Non-returnable 5 Gallon Bottle Design Non-returnable 5 Gallon Bottle Design
Non-returnable 5 Gallon Bottle Design Non-returnable 5 Gallon Bottle Design
 
Related Posts           Click Here to See More...
TopicsForum NamePost Time
Bottle Wall Thickness not Uniform (Radial) Blow Molding (Machine) 6/21/2013 7:56:52 PM
Bottle Neck Deforms Blow Molding (Machine) 5/27/2011 7:51:55 PM
Blowing Temperature of PET Blow Molding (Machine) 5/15/2009 3:09:38 AM
Preform Bottom Bursts while Stretching/Blowing Blow Molding (Machine) 7/20/2008 7:08:52 AM
Hot fill bottles - new design Blow Molding (Machine) 12/28/2006 4:36:32 PM
semi auto blow moulding machine Blow Molding (Machine) 12/2/2005 2:48:05 AM
requiest for pc blow molding machine Blow Molding (Machine) 11/13/2005 7:10:15 PM
PC bottles Blow Molding (Machine) 10/13/2005 7:49:40 PM
quatation\catolog Blow Molding (Machine) 9/28/2005 12:32:06 AM
blow moling process Blow Molding (Machine) 8/27/2005 12:24:34 PM
injection blow problem Blow Molding (Machine) 8/14/2005 5:39:40 PM
blow molding process of PETG Blow Molding (Machine) 6/29/2005 7:56:54 PM
Slight Odour Blow Molding (Machine) 6/22/2005 10:40:46 PM
 
[Plastics Project] [Plastics Machinery] [Plastics Mold] [Discussion Forum] [Contact Kenplas]
Copyright © 2017 Kenplas Industry Limited, Hangzhou Kenplas Machinery Ltd.              Powered by Alentus.